Silicone t-fitting for FSI engines:
Podi is proud to offer the BEST solution for the Audi/VW FSI engines if you wish to install a boost gauge.
This custom made silicone t-fitting is an exclusive product and makes boost gauge installations clean and easy.
Forget the other products which require multiple clamps to install and looks terrible when you are finished. No need for extra hoses, barbs or reducers!
Just insert our inline restrictor into the silicone fitting, pop off the cap on the intake manifold, slip the silicone t-fitting onto the bung and you are done!
Anti-Buzz inline restrictor fittings:
The anti-buzz inline restrictor fittings eliminate the vibration and noise of boost gauges when installed on automobiles with turbocharged engines.
Mechanical boost gauges use a feed line to directly measure boost pressure. Due to pulsations in the airstream a gauge vibration can occur and cause the gauge to rattle or “buzz.” This can be eliminated by adding a restrictor into the boost gauge feed line.
This inline fitting we have designed has a restrictor orifice built to our specifications in the center. This fitting is custom made injection molded piece and the restrictor opening is made to tolerances of 0.003".
Our design simplifies installation and retains boost gauge response time as compared to other solutions such as add-on in-line fuel filters or fittings that have melted plastic inserts to mimic a proper restrictor.
The inline fitting is designed to be spliced into the boost gauge feed tubing and can be easily retrofitted to existing boost gauge installations.
The restrictor have been tested to work with the following brands of mechanical gauges: Autometer, Defi, Omori, Stewart Warner
|
This SMY ClusterMaker Gauge Pod is a dual 52mm gauge setup that replaces the factory 2 piece cluster bezel.
Each Cluster is made from an Aluminum injection mold and made with 100% ABS plastic.
A UV protectant solution was added to the ABS injection to help with sun damage.
$140.00 USD
|
|
|
This SMY ClusterMaker Gauge Pod is a dual 52mm gauge setup that replaces the factory 2 piece cluster bezel.
Each Cluster is made from an Aluminum injection mold and made with 100% ABS plastic.
A UV protectant solution was added to the ABS injection to help with sun damage.
$150.00 USD
|
|
|
Opening fits a standard size 2 1/16" (52mm) gauge with a maximum depth of 0.8" (20mm)
US Patent No. D643,791
Note - OEM pleather trim piece is not included with the pod
$40.00 USD
|
|
|
Opening fits a standard size 2 1/16" (52mm) gauge with a maximum depth of 0.8" (20mm)
US Patent No. D643,791
Note - OEM pleather trim piece is not included with the pod
$40.00 USD
|
|
|
Opening fits a standard size 2 1/16" (52mm) gauge with a maximum depth of 0.8" (20mm)
US Patent No. D611,884
Note - OEM pleather trim piece is not included with the pod
$40.00 USD
|
|
|
Opening fits a standard size 2 1/16" (52mm) gauge with a maximum depth of 2.0" (50mm)
US Patent No. D539,914
$40.00 USD
|
|
|
Opening fits a standard size 2 1/16" (52mm) gauge with a maximum depth of 2.0" (50mm)
US Patent No. D538,720
Canadian Industrial Design No. 116788
European Community Design Registration 000570296-0001
$40.00 USD
|
|
|
Opening fits a standard size 2 1/16" (52mm) gauge with a maximum depth of 2.0" (50mm)
US Patent No. D593,913
$40.00 USD
|
|
|
Here is the latest mad scientist OCD idea that we have come up with... the Podi Powerstick power distribution system.
Wire up any one of the blocks to power (+V), ground (G) and one optional "whatever you want" input (A) and it automatically splits the same signals to the other 5 blocks!
Say goodbye to rats nest wiring! No more splicing and soldering!
Just run the wires to the Powerstick, tighten down the screws and you are done! Removal is just as easy!
The kit will include the following to help you adapt and hook up just about any 12V car accessory:
(12) 22-26AWG seamless nylon butt connectors
(4) 18-22AWG #10 spade terminal
(2) 24-26AWG Posi-Tap
(20) 4" cable tie
(1) standard size fusetap with 2A fuse
10 feet of 22AWG wire - red
10 feet of 22AWG wire - black
10 feet of 22AWG wire - yellow
$40.00 USD
The Powerstick is rated to 2A total current draw across the device.
|
|
|
These trim pieces are made of 3M vinyl and are attached outside the headlight to hide the ugly amber reflectors.
This is a very cost-effective mod for those who do not want to get ecodes or take the risk of opening their headlight housings.
The vinyl is precut using a laser cutter in order to provide 100% precision and are available in two colors: smoke and glossy black.
Your will get two vinyl pieces, one for each headlight, per order.
Please indicate your color selection at checkout.
$25.00 USD
|
|
|
Wheel hangers that are CNC machined out of aluminum. It is machined on one end to allow for a socket in case you get it stuck.
The hanger is 114mm (4.5") long and 12mm for VW and BMW fitiment and 14mm for Audi and Mercedes Benz fitiment.
$15.00 USD
|
|
|
3/16" diameter with integrated restrictor - sold in pairs as sometimes one just isn't enough
$5.00 USD
|
|
|
This fitting is to install boost tubing in tight clearance pods. Will fit most boost gauges with a threaded brass vacuum inlet on the back - Stewart Warner, VDO, Autometer, etc
$5.00 USD
|
|
|
This kit contains all of the bits and pieces you would need to wire up and power your gauge
The kit contains the following items:
(4) 22-26AWG seamless nylon butt connectors
(3) 18-22AWG #10 spade terminal for ground connection
(1) 24-26AWG Posi-Tap
(6) 4" cable tie
(1) standard size fusetap with 2A fuse
(1) mini size fusetap with 2A fuse
5 feet of 22AWG wire - red
5 feet of 22AWG wire - black
5 feet of 22AWG wire - yellow
$15.00 USD
|
|
|
This boost tap is used for the following engines:
2010+ Audi A5 TSI
2009+ Audi A4 TSI
2006+ VW Jetta/GTI 2.0T FSI & TSI
2005+ VW Passat 2.0T FSI & TSI
$30.00 USD
|
|
|
Includes 6' vacuum tubing, t-fitting, 2 anti-buzz inline restrictors, 90 degree barb fitting
$15.00 USD
|
|
|
100% cotton shirt in medium, large and extra large size
$15.00 USD
|
|
|
1" wide polyester lanyard with detachable keyclip
$10.00 USD
Free shipping for this product within North America
|
|
|
1.75" enamel keychain with split ring
$10.00 USD
Free shipping for this product within North America
|
|
|
Buy a combo and save $5.00!
$15.00 USD
Free shipping for this product within North America
|
|
|
Machine die-cut decal for your car.
White text with a red needle
Size is 18.0"Wx 6.0"H
$15.00 USD
Free shipping for this product within North America
|
|
|
Machine die-cut decal for your car, you get 2 per order.
White text with a red needle
Size is 5.0"Wx 2.0"H
$15.00 USD
Free shipping for this product within North America
|
|
|
Buy a decal combo and save $7.00!
$23.00 USD
Free shipping for this product within North America
|
|
